-
Posts
165 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by giovanni56
-
-
14 hours ago, Giandiego said:
Ho ricevuto un paio di AR6 pochi giorni fa. Purtroppo mancano entrambi i woofer. Ho venduto molti di questi AR6 nel 1975/77, quindi so che erano 8 ohm. Il problema è che sul retro della scatola la carta dice 8 ohm, ma entrambi i tweeter sono 4 ohm! Il crossover è il modello che indichi come "B", e i tweeter sono originali, vecchi, ma funzionano ancora molto bene. Qualcuno sa dirmi come è possibile? Molte grazie.
Did you measure the Re of the tweeters? what value did you. read?
-
1 ora fa, Carnivore ha detto:
Cosa sono quelle cose ovali? Qualcuno ha installato le porte? I miei non li hanno.
These LSTs are among the last ones produced, they do not have midrange and tweeter with external wiring, those oval things close the holes of the external terminals. The original tweeters have been replaced with 200011-1, the crossover network has been modified by inserting a high-pass inductance of adequate value and the tweeter connection is in antiphase with respect to the midrange and woofer.
-
After restoring this pair of Ar LST, I did some checks and to my great surprise, I found broken the 10 Ohm 10W resistor in parallel to the 2500 nF C and the fuse holders with a very high contact resistance value. I decided to remove the fuse holders and replace the faulty R; I wonder what could have been the cause of this breakage that I hypothesize could occur if the 2500 nF C was interrupted leaving all the power of the amplifier to pass on the resistor. Does anyone have experience with this? thank you.
-
-
Si tratta di una coppia di Ar LST a cui hanno sostituito tutti i tweeter Ar 200013-1 con AR / TNG 1200011-1 e il woofer Ar 200003, con Ar / TNG 1200003-AB dell'Ar3a Replica, quindi il filtro passa alto deve essere modificato; i midrange sono originali. Intendevo eliminare l'autotrasformatore ma non sono del tutto convinto.
-
-
-
On 19/3/2021 at 20:50, Giorgio AR said:
Basta acquistare questa coppia di primi AR3a, n ° H3a 3603 e 4342. La
mia grande sorpresa dopo aver rimosso le griglie incollate, in quella con n ° 3603 (questa probabilmente ha subito manutenzione negli anni) ho trovato il woofer con rivestimento in tessuto. L'altro altoparlante non è stato toccato e ha il woofer con rivestimento in schiuma, chiaramente per sostituire la schiuma!
Questa coppia è l'ottava che possiedo con woofer da 12 "e ne sono felice, finalmente ora possiedo un woofer da 12" con magnete in Alnico!La sorpresa subito dopo aver rimosso le griglie
Gli altoparlanti dopo aver rimosso le griglie fissano la colla e iniziano la pulizia
AR3a è con griglie
Etichette posteriori
Have you checked to see if the filters in the two cases have identical component values
-
In 1969 it happened to buy a pair of Ar3a with Alnico woofers, both with smooth and corrugated cone; it was difficult to notice the difference on the woofers, because the frames were glued and removing them would void the warranty. The engineer Gianfranco Maria Binari (later editor of SUONO STEREO HI-FI), in 1969, bought a pair of Ar3a, with a woofer in corrugated cone and the other smooth; he noticed it, because with a flashlight he illuminated the woofers through the front cloth; later he was able to get a pair with both smooth woofers from the seller.
-
On 26/2/2021 at 03:41, RoyC said:
Jnkns,
I tuoi esemplari sono le primissime versioni del 4x. I crossover sono originali di questa versione, con un condensatore da 20uf in serie al tweeter e un condensatore da 24uf in parallelo al woofer. Ho disegnato sulla tua foto per aiutare a chiarire il circuito. La staffa che tiene premuto il doppio condensatore da 20 uf / 24 uf fa effettivamente parte del circuito. vedi sotto...
Ho notato che la pentola nella tua foto è stata ricablata per bypassare il tergicristallo. Uno dei 2 fili verdi precedentemente collegati al terminale n. 1 è stato tagliato e saldato al terminale n. 2. È molto importante correggere questo problema quando installi i nuovi controlli di livello! (A proposito, i nuovi vasi che Kent offre sono un'ottima scelta per il prezzo.)
Roy
I'd be curious to measure the R of the bracket that's part of the filter wiring, which is under the woofer's low pass inductance
-
On 14/9/2015 at 20:48, Pete B said:
Immagina di mettere in parallelo tutti i componenti del crossover, funziona esattamente così:
1,6 mH va a 0,8 mH a metà del DCR
16 uF va a 32 uF
0,45 mH corrisponde a circa 0,22 - 0,25 mH
3 ohm vanno a 1,5 ohm
Hai crossover Rev 2?
16 uF va a 32 uF ??
I don't understand, with the switch in INCREASE, C1 and C2 are put in series and in this case, the capacitance is halved and becomes 8uF. Am I missing something?
-
-
-
5 hours ago, newandold said:
Congratulazioni! Quelle 3a sembrano essere state magnificamente restaurate.
Non sarei eccessivamente preoccupato per il raggio di rollio a meno che tu non stia notando un problema con i bassi ad alti livelli di volume, quando il movimento inizia davvero.
La preoccupazione principale che ho con i woofer vecchi come questi è la conformità dei ragni.
Spesso trascurati, possono sembrare a posto e senza crepe. Tuttavia, se la conformità è notevolmente inferiore rispetto alle specifiche originali, potrebbero più facilmente toccare il fondo rispetto a quando saranno nuove. I bassi più fluidi provengono dallo spider e dal surround che lavorano all'unisono per mantenere il controllo sulla bobina mobile.
Conto
The spiders are fine; after the refoam, I checked the T&S parameters, all ok.
-
1 hour ago, rjr513 said:
Hanno un bell'aspetto ... bel lavoro ... sono curioso di sapere dove hai preso le cupole e il materiale di sospensione per ricostruire i tweeter?
Everything made in Romagna, 😎
-
58 minuti fa, Aadams ha detto:
Quelli sono Sprag originali. Crossover non è stato ricapitolato.
The capacitors are original Sprague, but the wiring harness wires are not original. The wiring harness has been redone. The AR10's are among the earliest produced, they have the external protection fuse next to the input terminals.
-
1 hour ago, RickB said:
Ottimo lavoro, come suonano?
They sound very good; in my opinion, they are tops among the various Ar6 models
-
-
-
On 29/8/2011 at 21:59, Carlspeak said:
Sono state utilizzate schiume tipo Boston Acoustics (riempite).
I valori seguenti sono medi. di due test separati del woofer a seguito di una nuova schiuma senza rotture.
Fs = 16,8 Hz
Qts = 0,025
Le = 0,78 mH
Vas = 7,5 Cu. Ft
Mms = 70 grammi
Sens. = 87 dB
BL = 9,25
Sebbene di dimensioni inferiori (diametro esterno del telaio 10 "), le proprietà sopra ricordano quelle del woofer da 11" della serie AR3. Il woofer Cizek aveva persino un anello di schiuma attorno alla superficie del cono a circa 2 pollici dal tappo antipolvere.
Qts 0,025 ????
-
On 2/13/2021 at 8:53 PM, RoyC said:
Alcuni possessori di AR-11 / 10pi preferiscono i tweeter precedenti, che in genere hanno un output più uniforme. La versione con cupola nera tende ad avere un rendimento meno uniforme a causa della natura variabile del vecchio ferrofluido.
Roy
A prototype of Ar10Pone with slide selectors, was sent for testing to SUONO STERO HI-FI magazine in 1975. The test and measurements of the loudspeaker was conducted by engineer Renato Giussani (later ESB 706 designer), who reproduced, in the crossover filter scheme, the high pass of the tweeter with the 8 uF capacitor; by the way, the 8 uF value is also reported in sheet 15 of the spare parts list issued by Acoustic Research and indicated as spare part for the AR 10 (see attachments), part list 830025.
-
9 hours ago, RoyC said:
Ad eccezione dell'ultima frase, il tuo post è in italiano. Non sono sicuro di quello che stai chiedendo riguardo a un condensatore da 8 uf.
If I am not mistaken, the light hazel dome tweeters, which do not have ferrofluid, in the very early versions of Ar 10 Pi One (the ones with slide switches), had the high pass filter with 8uF capacitor and 0, 1 mH inductance, while all later versions had the 10 uF capacitor; Roy, could you kindly give me a confirmation about the tweeter and the 8 uF capacitor, thanks
-
Tweeter Ricostruzione AR3a:
1) Apparecchiature mobili e gruppo magnetico
2) Misurazione del peso dell'equipaggio mobile rotto
3) Misurazione del peso dell'equipaggio mobile rotto
4) Misura di R
5/6) Tweeter completato e cablato
7) Controllo e verifica centratura
8) Misura dell'impedenza e parametri T&S
-
On 15/2/2021 at 22:01, ar_pro said:
Finitura stupenda: sembrano nuovi!
Thanks
Odd measurement of old resistor in LST
in Acoustic Research
Posted
No it's not weird, on the last LST Ar manufactured Ar used those resistors as well. I found one that was faulty.