souk1501 Posted April 22, 2012 Report Share Posted April 22, 2012 This morning, I took out my pair of AR570 Powered Partners from a box after probably about 10 years of non-use. It worked for about 10 minutes then one of them lost power and can not be turned on again. Flipping the power switch have no response what so ever. Does anyone have any experience with this problem on this speaker? Thank you in advance for any help. Link to comment Share on other sites More sharing options...
JKent Posted April 22, 2012 Report Share Posted April 22, 2012 I had a pair purchased 2nd hand and one speaker did not work. Turned out to be a bad RCA connector. Simple. Of course your problem could be different. btw--the woofers will definitely need to be refoamed.This thread tells the story and also has a link to the schematic: http://www.classicspeakerpages.net/IP.Board/index.php?showtopic=4373&hl=%2Bpowered+%2Bpartners&fromsearch=1Kent Link to comment Share on other sites More sharing options...
souk1501 Posted April 23, 2012 Author Report Share Posted April 23, 2012 Thanks Kent. Surprisingly, the woofer of my working one still sounds good with no sign of dry rot. I did read your other thread before I started this one. My case seems to be more severe as I can't even get the power light to turn on. Hopefully I would be able to figure out what's wrong. My guess is something with the power module. Link to comment Share on other sites More sharing options...
powder70 Posted May 3, 2012 Report Share Posted May 3, 2012 I have disassembled mine in order to drill some custom mounting holes thru the enclosure without drilling wires or circuitry. Thats when i discovered the fuse on the main board unfortunately I was careless and actually dropped one off of the work table while it was hanging in pieces and damaged something on the board. Now all it does is blow fuses, currently bidding on replacement 570 on Ebay. Just wondering if you knew about the internal fuse, take that puppy apart........just dont drop it Link to comment Share on other sites More sharing options...
bitman Posted May 24, 2012 Report Share Posted May 24, 2012 I can not find instructions for disassembling the AR570 Powered Partners. I remove the Allen screws in back but I can't get them apart. Any help would be much appreciated. Link to comment Share on other sites More sharing options...
JKent Posted May 24, 2012 Report Share Posted May 24, 2012 I think they may just be stuck. There may be a gasket IIRC. Just pry them open. Here is a photo of the case open. I no longer have these and am relying on memory. Good luck.Kent Link to comment Share on other sites More sharing options...
bitman Posted May 25, 2012 Report Share Posted May 25, 2012 I tried again and best I can do is distort the front of the enclosure. Do the Phillips screws under the very back panel hold the front? I can turn them but they feel like they are turning something inside. Link to comment Share on other sites More sharing options...
JKent Posted May 25, 2012 Report Share Posted May 25, 2012 I'm sorry I no longer have mine. Maybe someone else can chime in. According to the photos I have there were 8 hex-socket head machine screws on the back and I'm pretty sure all 8 have to be removed, but maybe not. The 4 in the middle are for attaching the "clamp" so the speakers can be mounted on a pole. What about the knobs on front? Do they pull off?Maybe search "powered partners" in the AR forum, find members who have worked on them and send PMs.Here is a manual for the similar Advent 570 http://www.digitalhy...V570_Manual.pdf These are also known as Recoton AV570. All very similar. According to the Advent manual they have removable grilles. I don't recall whether the AR grilles snap off but maybe try (gently) and see if they snap off.I seem to recall seeing an exploded diagram recently. May have been on a Sears parts site--but I can't find it.Kentedit: Found it. Don't know how helpful it is though: http://www.searspart...6&prst=&shdMod= Link to comment Share on other sites More sharing options...
bitman Posted May 25, 2012 Report Share Posted May 25, 2012 Thanks a bunch Kent. I have looked at the diagrams and photos. The knobs and controls appear attached to the fronts. I removed all eight cap screws. I can pry the shorter sides up enough to get a small pry bar in but it then feels like I'm about to crack the plastic surround. Already dinged up the cast metal housing. Link to comment Share on other sites More sharing options...
JKent Posted May 25, 2012 Report Share Posted May 25, 2012 sorry you are having such trouble. Look at the photo in post #6. That whitish tube in the middle of the long side is an insulator for a long machine screw IIRC. Other than that, I don't recall anything holding the long sides, except glue or gummy gasket stuff. Definitely be careful about cracking 30-yr-old plastic but I wonder if you ran a mat knife or x-acto knife along that seam, if it would loosen it a bit. Attached is a close-up of a corner. You may be able to see there is, I think, a groove in the housing with some sort of rubber gasket in there. You can also see that the front plastic part has brass inserts for the machine screws. You mentioned one of the screws keeps turning--probably the insert has come loose.Kent Link to comment Share on other sites More sharing options...
bitman Posted May 25, 2012 Report Share Posted May 25, 2012 One more thank you. From that photo I also see the knurled end of a brass threaded insert in the face. It is possible that is binding where it presses into the back. I'll try again. Link to comment Share on other sites More sharing options...
bitman Posted May 25, 2012 Report Share Posted May 25, 2012 Bingo! Two more screws under a rubber flap inside the mounting panel on the back. Link to comment Share on other sites More sharing options...
JKent Posted May 25, 2012 Report Share Posted May 25, 2012 Great!The score:Bitman 1Forces of Evil 0Sorry I had forgotten about those 2 screws.Kent Link to comment Share on other sites More sharing options...
bitman Posted May 25, 2012 Report Share Posted May 25, 2012 I had seen those screws and loosened them. But they seemed to be twisting something inside so i tightened them up. I was worried the we attached to a component. Turns out it was insulation.Great forum. First time here. Link to comment Share on other sites More sharing options...
JKent Posted May 26, 2012 Report Share Posted May 26, 2012 a belated welcome!Now that they are open, you'll want to re-foam the woofers. I got the kits for my PPs (and ALL my refoam jobs) from M-Sound. Here is his ebay page: http://stores.ebay.c...sid=p4340.l2563And here is his website, where you'll find very detailed step-by-step instructions: http://www.citlink.net/~msound/refoam/Be sure to follow Powder70's advice about the fuses. If I were doing this today, and keeping them, I'd probably replace all the capacitors.Kent Link to comment Share on other sites More sharing options...
bitman Posted May 27, 2012 Report Share Posted May 27, 2012 The reason I wanted to open mine up is I have a little rattle in the sound. Would that be the foam or something else? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.