ligs Posted August 26, 2018 Report Share Posted August 26, 2018 (edited) High Sensitvity 92 db 2-way Speakers Using JBL 127H-1 and Dayton RST 28-4F The modern high quality HT speakers tend to have typically 86db/2.83v sensitivity, limited primarily by the relatively smallish woofers used in them. The newly introduced Dayton RST-28F4 has a sensitivity of 93.5db even without a waveguide or horn. In addition, it can be crossed low(1400 hz). I jumped at the opportunity to use it in a pair experimental 2-way high quality DIY speakers with sensitivity around 92 db/2.83v. For the woofer, I just happen to have a pair JBL 127H1 woofers available. JBL127H1 has advanced magnetic structure, 2-inch voice coil and was used in many commercial and professional speakers (4410A, XPL 160A, L80T and T3). The measured sensitivity was 92db with very low distortions (less than 0.5% even at 95db SPL for most frequencies), according to a review by High Fidelity magazine. In a fully stuffed sealed cabinet of 0.7Ft3, I estimate the Q of the box will be around 1.1 and -3 db around 60 hz, plenty low for a HT speaker. One can choose other options if deeper bass is desired. TS parameters and suggested enclosure sizes are published here. http://ampslab.com/blog/2018/05/06/jbl-127h1/ The current crossover (GS-1) is voiced mostly by listening and probably can be simplified further. My reference speakers are Infinity Reference 162 as reviewed here. https://www.soundandvision.com/content/infinity-reference-r162-speaker-system-test-bench. My big surprise is the spectral balance of my JBL127H1 /RST28 F4 is very similar to Infinity R162 and certainly no lacking of details and spaciousness. I would rate the transient response of both speakers to be equally outstanding. I can listen to either speaker for a long time without listening fatigue. In conclusion, you can build a higher sensitivity speaker by using a high quality large diameter woofer without losing sound quality. Edited October 8, 2018 by ligs spelling Quote Link to comment Share on other sites More sharing options...
Aadams Posted August 26, 2018 Report Share Posted August 26, 2018 13 minutes ago, ligs said: For the woofer, I just happen to have a pair JBL 127H1 woofers available. JBL127H1 has advanced magnetic structure, 2-inch voice coil and was used in many commercial and professional speakers (4410A, XPL 160A, L80T and T3). Is this the same woofer below? This is an LSR 6332. Quote Link to comment Share on other sites More sharing options...
ligs Posted August 26, 2018 Author Report Share Posted August 26, 2018 LSR 6332 has a newer 12" woofer. The picture of JBL127 H1 is here. It has a nice cast frame and a nice large magnet. Quote Link to comment Share on other sites More sharing options...
ligs Posted August 28, 2018 Author Report Share Posted August 28, 2018 Just put the tweeter in a more permanent housing. There is a strip of felt between the bottom of the tweeter and the top of the woofer cabinet to reduce the diffraction effect. Both male and female sound very natural. I did not expect the midrange could sound this good with a 10 inch woofer crossovered to a 1 1/8" tweeter. The same configuration works well with an 8" woofer(Dayton RS225-4) too. n. Quote Link to comment Share on other sites More sharing options...
Aadams Posted August 28, 2018 Report Share Posted August 28, 2018 I can't find where you told us the crossover frequency. Quote Link to comment Share on other sites More sharing options...
ligs Posted August 28, 2018 Author Report Share Posted August 28, 2018 The tweeter highpass crossover is very similar to that of http://techtalk.parts-express.com/forum/tech-talk-forum/42977-my-rs180-mtm-design Therefore the crossover frequency is estimated to be around 1500 hz similar to in the above design. The woofer crossover has gone through a few reiterations, starting with a simpler 2nd order but ending in 2 inductors ,2 capacitors and a resistor. For someone who can do sims the parts number probably can be reduced. Quote Link to comment Share on other sites More sharing options...
ligs Posted September 2, 2018 Author Report Share Posted September 2, 2018 While I was listening to a solo guitar CD from Journey to the New World by Sharon Isbin, I noticed it sounded somewhat flat not as vibrant as the real guitar would. Recalling Stereophile review of JBL XPL 160(the same woofer was used), the midrange and tweeter were stepped back from the woofer so the voice coils of all 3 drivers would be aligned in the same plane. https://www.stereophile.com/content/jbl-xpl-160-loudspeaker. The illusion of space thus the imaging of these speakers did improve considerably by moving each tweeter backward for about 3.5 inches from the edge of the woofer cabinet. With this tweaking, the solo instruments like guitar and violin now sounded better than before. I continue to marvel that our hearing is a lot more sensitive and complex than perhaps the microphones are capable of detecting. Quote Link to comment Share on other sites More sharing options...
ligs Posted October 8, 2018 Author Report Share Posted October 8, 2018 Dayton audio recently introduced 2 new reference series 28 mm dome tweeters(RST 28F-4 and RST 28A-4) replacing the highly praised RS 28F-4 and RS 28A-4. The F version is soft fabric dome and A version is hard anodized aluminum dome. The RST 28F-4 and RST 28A-4) now have 92.5 db and 93.5 db sensitivity, some 3db more sensitivity than their predecessors. The combination of high sensitivity and the ability to cross low as 1400-1500 hz make them extremely attractive for DIY projects. Carspeak even recommended RS 28F-4 as a replacement tweeter for Advent NAL with highs extended flat to beyond 20k hz. I have been playing several reiterations of JBL 127 H-1/Dayton RST 28 F-4 for months. The latest crossover (GSL-A) represents the most balanced sound so far. The same crossover works also with RST 28 A-4. Both F and A versions are highly listenable. Quote Link to comment Share on other sites More sharing options...
Aadams Posted October 8, 2018 Report Share Posted October 8, 2018 Maybe I am missing the point here and a bit naive but couldn't you use a DSP amp to power and crossover these speakers and dispense with the the hand-made crossover. There may be disadvantages I don't see but one advantage would be you could set the hi/lo pass frequency by pushing a button. Adams Quote Link to comment Share on other sites More sharing options...
ligs Posted October 8, 2018 Author Report Share Posted October 8, 2018 Good question. I would probably try that some day. Interestingly, many expensive speakers such as Wilson and Revel still use passive crossovers while in theory they could use DSP and be done with it. I don't know if it has to do digital(DSP) vs analog(passive). What do you think? George Quote Link to comment Share on other sites More sharing options...
Aadams Posted October 9, 2018 Report Share Posted October 9, 2018 6 hours ago, ligs said: What do you think? I do not have the knowledge to create a handmade custom crossover. The only way I would know how to do it is with a DSP. A stereo power amp with an integrated DSP would be most convenient but you would need an amp for each pass band. For a 3way speaker you would need 3 amps. The only ones I know about are the Crowns which are programmed to use Linkwitz Reilly 24db octave. I haven't seen any outboard DSPs that are not made for powered speakers and even then more for surround sound use. I notice MiniDSP has a 2x8 outboard processor specifically for stereo inputs but still need a power amp for each pass band. 3 way six channels 4 way 8 channels. Adams Quote Link to comment Share on other sites More sharing options...
ligs Posted October 9, 2018 Author Report Share Posted October 9, 2018 I searched the literature for comparing speakers using passive vs digital crossovers(processors). The first one is not an apple to apple comparison between Revel 106M vs NHT Xd Active DSP System. https://hometheaterhifi.com/reviews/speaker/bookshelf/revel-performa3-m106-2-way-bookshelf-monitor-loudspeaker-review-part-three/ The second one is a comparison between passive KEF LS 50 vs KEF LS 50 wireless(active DSP). https://forum.audiogon.com/discussions/kef-ls50-wireless-vs-passive I admit I am an old fashioned hobbyist who enjoys playing with surplus electronics parts. The speakers with passive crossovers allow me more opportunities to keep busy:) George Quote Link to comment Share on other sites More sharing options...
Aadams Posted October 10, 2018 Report Share Posted October 10, 2018 On 10/9/2018 at 7:13 AM, ligs said: I searched the literature for comparing speakers using passive vs digital crossovers(processors). I read the articles about the speakers with on board DSPs. IMO it doesn't make sense from a hobbyists standpoint because the DSP can't be reprogrammed but it is an advantage for the consumer because the DSP is customized to operate with a single amp per stereo side. DSPs outboard with respect to the speaker, would be perfect for a hobbyist wanting to select and test a variety of drivers in combination. Passive speakers in combo with outboard DSPs is a more flexible arrangement but requires an amp per pass band on each channel. I think the line array systems setup on big music venue sound stages are done this way. At home it would not be any different than bi-amping, tri-amping or even quad- amping a stereo pair of speakers but the crossover would be entirely outboard and programmable. Speaker system manufacturers could bypass or eliminate passive crossovers and specify the recommended crossover settings to be set in an outboard DSP crossover. Edit: Just found a nerd thread from 2017 about this very topic. https://audiosciencereview.com/forum/index.php?threads/crossover-less-passive-speakers.1951/ Adams Quote Link to comment Share on other sites More sharing options...
ligs Posted November 1, 2018 Author Report Share Posted November 1, 2018 Experimenting further with a LCR trap in woofer’s crossover removed a slight hump around 1000 hz. This improved the vocal quality of JBL127H-1/RST 28 A-4/NHT 1259. Here is a comparison of my DIY satellite vs commercial JBL Studio 36ii (6" three -way)and Infinity Reference R162(6" 2-way) speakers. Above 2000 hz all three have very similar response curves. Please disregard 200 hz and below because of the room effect. I can live happily with any of the three choices. On louder passages, the JBL127 H1 sounds more relaxed, perhaps its low distortion is a contributing factor. George Quote Link to comment Share on other sites More sharing options...
Aadams Posted November 1, 2018 Report Share Posted November 1, 2018 36 minutes ago, ligs said: JBL Studio 36ii (6" three -way Ligs What is the approx. model year for those JBLs 36ii and are they ported? I found them but no dates. That six inch speaker will strain down low IMO. Was it playing full range or do you have the low range constrained as with the JBL 10"? Otherwise I am not surprised the 10" sounds more relaxed at higher sound levels. Adams Quote Link to comment Share on other sites More sharing options...
ligs Posted November 1, 2018 Author Report Share Posted November 1, 2018 My guess is around year 2000. They look like this. Yes it has a 6.5 " heavy duty cast frame woofer but is sealed. http://xcsdfarew.blogspot.com/2013/03/jbl-studio-s36aw-ii-3-way-high.html I am surprised it has a very complex crossover.(mixed 2nd and 3rd order slopes). I was playing them as full range in parallel with NHT 1259's. The rest of Studio series are vented. Stereophile has a review of its 8" big brother S-38. https://www.stereophile.com/standloudspeakers/365/index.html George Quote Link to comment Share on other sites More sharing options...
ligs Posted March 18, 2019 Author Report Share Posted March 18, 2019 While the original high sensitivity JBL 127H-1/RST28 A-4 2-way gives me satisfactory listening pleasure. I can not resist trying out another nominally 92db sensitivity setup by applying an old trick by stacking two identical speakers for each channel. Each of my 4 Infinity Reference R162 has a sensitivity of about 86db/2.83v. If you connect a pair of R162 in parallel, you will get about 92 db/2.83v. Because the stacked speakers will draw twice the power than a single plus some mutual coupling from the multiple drivers. cohttps://www.soundandvision.com/content/infinity-reference-r162-speaker-system-test-bench. How about the sound of stacked Infinity R162’s? I would say stacked arrangement sounds more dynamic and more tactile (there seems to be more bass and deeper too) than the singles. But I have to be very careful about listening at high sound volume to avoid over-driving either the speakers or the amplifier. Therefore, I have decided to insert a large value capacitor to rolloff some of the bass to the stacked speakers. Infinity uses a 390 uf NP capacitor to control the 75 hz cutoff for its Cascade Model 3 satellite. Last year, I purchased a pair of Cornell Dubilier, 947C361K801CAMS, Polypropylene Film Capacitors, 360uF, 800VDC. I by-passed each 360 uf cap with a 12uf ASC film cap and a 0.1 uf ASC film cap to constitute a total of 372 uf for the same purpose. Finally, with a 372 uF in series with the each channel of the stacked R162 and connecting with my pair of Dayton RSS390 HF4 subs, I get to listen to the new “stacked Infinity R162/RSS 390 HF4” arrangement. It will take me a while to get used to the new setup. My initial impression is they sound very transparent and clean! George Quote Link to comment Share on other sites More sharing options...
Aadams Posted March 18, 2019 Report Share Posted March 18, 2019 I was sitting at the keyboard when you posted this. Have been wondering if you had done this before and rejected it. Did you acquire additional Infinity boxes for this or reconfigure some satellite speakers. Are they 6" or 5" mids? Quote Link to comment Share on other sites More sharing options...
ligs Posted March 18, 2019 Author Report Share Posted March 18, 2019 I have many sets of Infinity R162 (6.5" midwoofer )and R152(5" midwoofer), acquired when Harman had periodic sales. Personally the mid and high range of the current series of Infinity reference speakers are my favorites. I read about stacked Advents but never owned multiple sets of the same speakers so I never tried stacking before. Honestly I did not think about stacking speakers until this week, more of an accident than a deliberation. I did have some success with D"Appolito MTM setup composed of 2 AR 4" Midwoofers (from AR Partner series) and one Dynaudio D28 Tweeter(idntical to the one used in the original D'Appolito paper. D'Appolito was using 5" Focal Midwoofers for the M part. While having only 0.5 ft3 sealed volume in each cabinet, they sounded very good. I did not have to worry about the low impedance because I was driving them with a Adcom GFA 555-2. In a MTM arrangment, a single tweeter is flanked by two midranges or two midwoofers. Therefore MTM is benefited by something akin to stacked configuration namely higher efficiency and symmetrical dispersion. Quote Link to comment Share on other sites More sharing options...
Aadams Posted March 18, 2019 Report Share Posted March 18, 2019 IMO that 6.5 is perfect with your subwoofer. Quote Link to comment Share on other sites More sharing options...
ligs Posted March 18, 2019 Author Report Share Posted March 18, 2019 1 hour ago, Aadams said: IMO that 6.5 is perfect with your subwoofer. I was trying to add my experience with D'Appolito MTM to my post. Strictly speaking MTM can be viewed as MTTM ( stacking) with only one T. Actually my MTM's with two AR 4" midwoofers and a Dynaudio D28 were my only living room speakers for many years until the foams began to rut. In spite of the small 4" woofers they had such a nice balance and clear vocals I just did not want anything else for a while. I am certainly hopeful that the stacked MTTM 6.5 will work well with my subwoofer. Quote Link to comment Share on other sites More sharing options...
Aadams Posted March 26, 2019 Report Share Posted March 26, 2019 On 3/18/2019 at 1:14 PM, ligs said: am certainly hopeful that the stacked MTTM 6.5 will work well with my subwoofer. Are they still stacked? Have you tried other configurations? Quote Link to comment Share on other sites More sharing options...
ligs Posted March 26, 2019 Author Report Share Posted March 26, 2019 3 hours ago, Aadams said: Are they still stacked? Have you tried other configurations? At this point, the upper range of the stacked pair sounds too analytical and a little harsh for my taste while they are nice and balanced when played in singles. In another word, the octave -to-octave balance of the original speaker is perturbed by stacking. Quote Link to comment Share on other sites More sharing options...
ligs Posted March 27, 2019 Author Report Share Posted March 27, 2019 Pointing the top pair of Infinity satellite speakers outward as what Bose recommended for its dual cube smoothed out the harshness a lot. Since I can rotate the top satellite speakers independent of the bottom ones , the next thing I tried was pointing the top speaker backwards to form a pseudo-bi-polar pattern. It did give a more spacious sound field and was quite enjoyable. Quote Link to comment Share on other sites More sharing options...
Aadams Posted March 27, 2019 Report Share Posted March 27, 2019 14 hours ago, ligs said: a little harsh for my taste while they are nice and balanced when played in singles. In another word, the octave -to-octave balance of the original speaker is perturbed by stacking. I too thought the same thing when the drivers were all aligned in the same direction. The sound can be made more diffuse and pleasing with a small offset from centerline. The new JBL Pro LSR 305s and 306s look good as single units for this type of application. According to their boilerplate they are designed to have a wide sound field, internally powered and biamped and designed for 80-100hz sub woofer crossover. The price seems right for sure. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.